![]() ![]() I asked if the motor could just be burned out and they said more or less it couldn't be. Another call to Wayne Dalton and they advised me to check my potentiometer gap, which I adjusted, and it still didn't work. ![]() I put that in and the unit still didn't work. Well, after I called Wayne Dalton for help with troubleshooting, they told me that my unit does not have a replaceable fuse and sent me a new motor control board (the whole circuit board). Can't anything ever be easy?!?Īttached File: Wayne Dalton idrive Fuse Replacement 314883 Rev2 9-29-2004.pdf (234 KB) I just found something at the Wayne Dalton Web site that explains what I have to do. It is installed on a 16x7 Wayne Dalton door and I know I have a Torquemaster idrive. The original unit was installed in 2003 and replaced under warranty a few years ago. Wayne dalton idrive install#Not sure what model I have since the original install slip doesn't say and the manual lists several on the cover. Wayne dalton idrive how to#I believe I have a problem with the fuse based on what I read here, but when I take off my white cover, the circuit board is not facing me, but is on the top in a horizontal fashion and I can't figure out how to get it out to look for a fuse. You guys saved me a service call from the professionals. I went back to Wayne Dalton site and could not find anything about checking the fuse. I came to this site and there it was, the fuse. I went to Wayne Dalton website but could not find the answer. Wayne dalton idrive free#I had to use the release cable to free the door. For whatever reason my door jammed on the way up. See "deceptive post" on this thread: iDrive versus Liftmaster 3800 They are most likely written by deceptive Chamberlain Internet marketers. Dalton units - but mine works fine.ĭon't worry about the horror stories. This unit was here when we bought this house 2 years ago. So I temporarily put a rigged jumper in the slots. ![]() So, I removed the circuit board, easy, pops off! saw 2 little round fuses. I read your note about a "FUSE" on your model. I hoped there was a fuse or circuit breaker on the control board, but have no owner's manual. Then I finally got things straight, manually lowered the door - but then no response to the button. Needless to say, the motor tried to raise the door - struggled beeped and stopped. When finished, for some stupid reason I manually raised the door, re-engaged the disconnect, and pressed the button on remote. raised the door by hand half way, set a garbage can under it to hold while I worked. I screwed it up when I was working on the doggie door in my garage door. It was 2 beeps (or beep buzz beep buzz) which is usually fixed by hitting the profile button as I've had to do twice before and is the answer in the not so useful troubleshooting, but this time it just gave 2 beeps then 2 more. I've had my iDrive for 6+ years now and it stopped today. If it completely stops moving, it's likely that the fuse is blown. The box included two fuses and instruction on how to replace the fuse.ĭid the fuse replacement fix your problem? I also couldnt figure out why my opener quit working but never called the company.I just started to troubleshoot on my own and found the blown fuse. To get the idrive going, I drove to the Radio Shack and bought a pack of four fuses.Ī few days later, I received the fuses from Wayne Dalton (see photo below). It could be purchased at Radio Shack, but they will send me the part for free. The customer service explained to me that the fuse it uses is the 250-volt, 4-amp slow-blow fuse (see photo below). The white panel on the right covers the motor control circuit board (see photo below) and the power circuit.Ī fuse is on the top left hand corner of the circuit board. In the end, they asked me to remove the white panel on the right by unscrewing two Philip screws on the bottom. They led me though a number of sequence to deduce the problem. Calling the customer service resolved the problem quickly. When I pushed the up/down button and the profile button, the garage door opener just chirped and beeped. At one point, it stopped moving altogether. But nevertheless, it had caused my Wayne Dalton idrive for Torsion Spring to fail. Whether it's due to the earth shifting or the old cable drum about to fail is still being debated. Recently, my garage door became off-balance. Wayne Dalton idrive Troubleshooting Tip #1 - Check the Fuse ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |